The rack I got from Rhino-Rack is the Pioneer Tradie rack. Tighten M6 crossbar bolts to 3-4NM 2-3lb/ft. Re-zip protective cover to 70mm from the top. You should read the PDS available at club4x4.com.au to decide if this product suits your needs. All Rights Reserved   |  Fit to bracket. reduce that spec to 49kg. The Rhino-Rack Folding Aerial Bracket is designed with versatility in mind offering 180 degrees of rotation for aerials, antennas, flags, small LEDs and spotlights. Remove the Hard Top (as per manufacturer's instructions) and place onto a stable safe working area. There are some brilliant tie down attachment Free Shipping on Orders Over $75. This Rhino-Rack Backbone 3 Base Mounting System is engineered to fit 2018-2021 Jeep Wrangler JL 4-door models. Prado 150, Rhino-Rack Backbone, Kings Awning install I hope everyone had a great Christmas and new year! Fit to bracket. 2A Assemble the support struts as shown. Make sure to fasten your load securely. 241436, (Hollard). Installation Time 3 … Wrangler JK. We decided on the Rhino-Rack Backbone and Platform for a Place the Hard Top back onto the Jeep (refer to manufacturer's instructions). Metal Tabs Front View: Fix the Backbone in place using M8 x 16mm Dome Head Screws and M8 Spring and Flat Washers. Aiden, Hi, did you have to do anything with the antenna when installing the rack on the Everest or does it fit comfortably? The Backbone Rack System may be used in off road applications, however a safety factor of 1.5 is enforced. Finger tighten. Front Holes Only: Using a 6-18mm step drill bit, open out the front spot holes as shown. Go easy on me, as this is my first time writing such a detailed review on a product, but given the lack of information on this product and the 5th Gen 4Runner, I felt compelled to share. as low as possible), the total final height of the vehicle was only 1.95 (backbone and platform) weighs 31KG, Nissan Navara (needs rivnut installation and only available for models without roof rails), Toyota When these roof racks are to be used on a vehicle that is driven off sealed roads the maximum load rating must be divided by 1.5. With the Centre Bracket aligned, spot mark the bracket position as shown. The Rhino-Rack Backbone is an interior structure set up on the inside of the JEEP JK Wrangler 2 door. I initially installed our Pioneer Platform using the Backbone because I wanted to keep the height to a minimum (both for carparks and centre of gravity reasons) but found the noise intrusive in the cab, even with the wind deflector fitted. Fit to bracket. manageable, The number of accessories and flexibility this Free Shipping Offers are for Standard Ground Delivery Service and are only valid for shipping addresses within the 48 contiguous United States. Very cleverly, the rails on the I’m waiting on delivery of the wind deflector to see if it also helps. Max: 100 (220lbs) - Two Crossbars.Read through instructions before installation. Cut under bar strips to fill the gaps.Note: Re-check all fasteners are secure. Repeat this process for the Centre bracket. You'll see it on the item page as a Vendor Handling fee, and it will show up in the cart below the item(s) you're ordering. Line the bracket flush with the contour of the Hard Top as shown. With rear bracket now secure, drill out the top fixture point with a 6.5mm (1/4") bit. Remember to subtract the weight of the roof racks to determine your maximum permissible load capacity. 18. The Rhino Rack Backbone mounting system is a sleek and stylish option for mounting your pioneer system and is available for a wide range of vehicles, with new models being released regularly Local to Western Australia. 25. cover that product in another review. 16. Honestly it took longer to clean the entire length of the channel then it did to remove the rack. Tighten from the outside with a 4m allen key. With relation to the Centre bracket, take corresponding foam pads and remove the protective strip as shown. The Rhino-Rack Backbone is a mounting system for your Toyota Land Cruiser 200 Series. Install Pioneer Underbars with slots indicated (42100,45100, 42101 or 45101). 8b With the front bracket template placed onto the Hard Top, align as shown and mark spot. Privacy Policy Rhino-Rack, 3 Pike St, Rydalmere NSW 2116, Australia Document No: R1698 (02) 8846 1900 Prepared By: Kayle Everett Issue No: 03 rhinorack.com.au Authorised By: Chris Murty Issue Date: 12/07/2018 These instructions remain the property of Rhino-Rack Australia Pty. You simply turn the rack over, and then adjust the rails to Started the process of installing my Rhino Rack platform rack. To cover any defects in material and workmanship, this mounting system is backed by a 5-year warranty. platform provides, To effectively manage weight – our system install. 2003-2021 ExtremeTerrain.com. It is important to be accurate when marking. 31. taking up cargo space in the vehicle. Backbone RFRB1 Automobile Accessories pdf manual download. See below for the detail: The below cars need the interior roof lining dropped to install Backbone: The below require a trackmount* installed to mount the platform: *note a trackmount is a track that gets installed into the existing roof ditch. 3 bars 120kg                                                    3 bars 80kg(264lbs)                                                           (176lbs)2 bars 100kg                                      =            2 bars 66kg(220lbs) load rating (Urban road)                  (145lbs) load rating (Off road)Load rating not taking into account crossbar weight - 5kg. The very first accessory that we decided to add was a Roof The Rhino-Rack Backbone is a mounting system for your Toyota 05/2029 onwards Rav4 with factory roof rails, all fitting done from the top, no inmternal lining drop to install… $ 496.00 or 4 payments of $ 124.00 with Afterpay Line up the mounting points of the bracket to the those exposed points on the roof, revealed in the previous steps. In another post, we will be doing an install of the Rhino-Rack + Backbone Kit. Exploring the great outdoors is more appealing than ever. Roofracks and vehicle can be damaged if the item transported is rigidly fixed at points on both the cabin and canopy. Line up the mounting points of the bracket to the those exposed on the roof in the previous steps. Replace the hardware removed in step 1 on both sides of the inner Hard Top. Notify me of follow-up comments by email. 1. And at 21 KG, 13. Metal Tabs face in toward the vehicle. Place the REAR bracket in place. 11. This is my review on Rhino-Rack’s Backbone system and Pioneer platform. points, and also smart things like folding antenna mounts, jerry can holders and of the rear is tightened, and then the process is repeated at the front, before Hi David, Required fields are marked *. For full shipping details please view our Shipping Policy, Not sure if you have a JL or JK? there is a 69KG capacity, which is really not a lot. number of reasons: Our Everest happens to be one of the vehicles that requires Start carefully securing Backone by tightening M8 socket hardware into the roof fi xed mount points with a 6mm Ball End Allen Key. Given the platform and backbone weighs 31KG, I ordered the 84”x49” (full length) Pioneer platform. if it was closer to the max-3 price i would go the route of the rhino pending the weight raiting. 20. If you have a 2018, confirm that you have a JL or JK. modular. 24. pressing things to carry. Do you mean the factory one at the top on the rear? I can confirm that a Backbone kit is available for the NP300.